Autonatomy · ADAS Vehicle-Specific Assignment Center

Forward camera / windshield / camera service

Camera Practical Assignment

Research the actual OEM requirements, establish vehicle and workspace readiness, perform only instructor-authorized steps, then document verification evidence.

1 · Vehicle & OEM procedure record

Student

Instructor

Date

Year / make / model

VIN or training unit ID

Mileage

Service event / complaint

OEM service-information source

Procedure revision/date

Instructor-authorized task

2 · Readiness gates

Every item must be verified from the actual applicable procedure or by instructor inspection. These are readiness prompts, not universal OEM prerequisites.

Correct vehicle/procedure identifiedRequired tools/targets/equipment availableVehicle condition meets listed prerequisitesWorkspace or route meets listed requirementsRelevant DTCs/warnings reviewedMounting/repair condition inspectedBattery support / scan access readyStop-work conditions discussed

Readiness: 0 / 8 verified

3 · Instructor-observed performance

#	Criterion	Observation	Evidence / note
1	Confirms correct vehicle and service event
2	Locates current OEM ADAS procedure
3	Identifies required calibration method and prerequisites
4	Checks camera mounting/glass/visible area as applicable
5	Confirms tire/ride-height/loading prerequisites as specified
6	Confirms steering/alignment prerequisites as specified
7	Sets up required battery support and scan equipment
8	Prepares facility/road conditions required by procedure
9	Uses specified target/equipment only where required
10	Performs measurements/setup without substituting generic values
11	Responds appropriately to a failed or blocked procedure
12	Completes required post-scan/verification steps
13	Documents procedure source, results and unresolved issues
14	Uses safe stop-work judgment when prerequisites are not met

4 · Completion evidence

Calibration / relearn result

Post-scan / warning status

Road/static verification evidence

Unresolved conditions / hold reasons

5 · Instructor disposition

Disposition

Instructor initials

Reassessment date

Remediation / next practice

Forward/side radar / collision-repair service

Radar Practical Assignment

Evaluate mounting integrity and repair history, research OEM calibration requirements, perform only authorized service, and document evidence before any release decision.

1 · Vehicle & OEM procedure record

Student

Instructor

Date

Year / make / model

VIN or training unit ID

Mileage

Service event / complaint

OEM service-information source

Procedure revision/date

Instructor-authorized task

2 · Readiness gates

Every item must be verified from the actual applicable procedure or by instructor inspection. These are readiness prompts, not universal OEM prerequisites.

Correct vehicle/procedure identifiedRequired tools/targets/equipment availableVehicle condition meets listed prerequisitesWorkspace or route meets listed requirementsRelevant DTCs/warnings reviewedMounting/repair condition inspectedBattery support / scan access readyStop-work conditions discussed

Readiness: 0 / 8 verified

3 · Instructor-observed performance

#	Criterion	Observation	Evidence / note
1	Confirms correct vehicle and service event
2	Locates current OEM radar service/calibration procedure
3	Identifies required method, equipment and prerequisites
4	Inspects radar module, bracket and mounting area
5	Checks repair history/refinish/obstruction concerns
6	Confirms chassis/alignment prerequisites as specified
7	Sets up battery support, scan tool and required equipment
8	Establishes specified facility/road conditions
9	Uses approved target/reflector/positioning equipment as required
10	Performs setup without inventing tolerances or repair methods
11	Stops when mounting damage or prerequisites invalidate calibration
12	Completes required post-scan/verification steps
13	Documents source, setup, results and unresolved issues
14	Makes a defensible hold/release recommendation to instructor

4 · Completion evidence

Calibration / relearn result

Post-scan / warning status

Road/static verification evidence

Unresolved conditions / hold reasons

5 · Instructor disposition

Disposition

Instructor initials

Reassessment date

Remediation / next practice

Wheel alignment / chassis service with ADAS considerations

Post-Alignment ADAS Assignment

Connect alignment results to vehicle-specific ADAS service information, determine whether calibration or other actions are required, and verify the completed service path.

1 · Vehicle & OEM procedure record

Student

Instructor

Date

Year / make / model

VIN or training unit ID

Mileage

Service event / complaint

OEM service-information source

Procedure revision/date

Instructor-authorized task

2 · Readiness gates

Every item must be verified from the actual applicable procedure or by instructor inspection. These are readiness prompts, not universal OEM prerequisites.

Correct vehicle/procedure identifiedRequired tools/targets/equipment availableVehicle condition meets listed prerequisitesWorkspace or route meets listed requirementsRelevant DTCs/warnings reviewedMounting/repair condition inspectedBattery support / scan access readyStop-work conditions discussed

Readiness: 0 / 8 verified

3 · Instructor-observed performance

#	Criterion	Observation	Evidence / note
1	Confirms correct vehicle and alignment/service event
2	Locates OEM information linking chassis service to ADAS
3	Reviews before/after alignment measurements
4	Identifies steering-angle/yaw/other relearn requirements if specified
5	Checks sensor mounting and related damage history
6	Determines whether calibration is required for this vehicle/event
7	Confirms prerequisites before any calibration or relearn
8	Uses required scan/equipment procedure as specified
9	Avoids treating a successful alignment as automatic ADAS verification
10	Investigates DTCs/warnings before proceeding
11	Completes specified calibration/relearn where authorized
12	Performs required post-scan/road verification
13	Documents alignment and ADAS evidence together
14	Makes a defensible hold/release recommendation to instructor

4 · Completion evidence

Calibration / relearn result

Post-scan / warning status

Road/static verification evidence

Unresolved conditions / hold reasons

5 · Instructor disposition

Disposition

Instructor initials

Reassessment date

Remediation / next practice